Tractor front mounted garlic harvest machine, including bracket, hydraulic connecting rod, power conversion transmission system, bracket as the main supporting part. The utility model is characterized in that a plurality of groups of excavating and attaching devices arranged in parallel are arranged at the front end of the support, and the excavating and attaching device includes a lower excavating plow and an upper attached shovel. The upper attached shovel is arranged at the front end of the support and above the lower excavating plow. The rear end of the lower digging plow is provided with a connecting rod, which connects multiple groups of lower digging plows in series. The two shaft ends of the digging plow connecting rod are connected with the connecting arms of the digging plow below both sides of the support, that is, the lower digging plow is connected to the support. The connection points are on the arms on both sides of the bracket. In the bracket, that is, in the middle of the bracket, behind the ground shovel, and above the lower excavating plow, a stem-transmitting device is arranged. The utility model has the advantages of simple and reasonable structure, flexible and convenient use, good overall stability, and can cut the garlic stems cleanly, directly obtain finished garlic, improve production efficiency and reduce labor.
Tractor front mounted garlic harvest machine is a new generation of garlic harvest products developed by our factory’s scientific researchers through field exploration and experience accumulation. Does not hurt garlic. The four-wheeled crawler can be lengthened to walk freely in the sticky ground where garlic grows. The power output is a 168F gasoline engine with strong power. It can also perform various operations such as planting, fertilizing, ditching, and ridging, which can easily realize multiple functions in one machine.
1: Automatically and neatly pave and harvest, excavate, transport, shake soil, and pave at one time, saving labor.
2: Crazy work efficiency, the hand-held money harvests 3 to 5 mu per hour, and the four rounds of money harvest 6 to 8 mu per hour.
3: Strong versatility, one machine with multiple functions, suitable for ridged planting garlic and peanuts, not affected by ridge width and ridge spacing, suitable for different planting modes across the country, large plains, and small hills and mountains can be used.
4: High-quality machine quality. The excavating blades and drive chains of this machine are all specially made, with high abrasion resistance and strength. The general user replaces the blades once every two years. The chain can be replaced by buckles at a low cost.
5: Scientific and reasonable design, adopting gear and chain transmission, running smoothly without power loss, and can work all-weather.
6: Tractor front mounted garlic harvest machine is equipped with a seedling support device, which can harvest fallen peanuts and garlic crushed by wheels.
7: The digging depth can be adjusted. This machine is equipped with a manual depth adjustment device, which is convenient and quick.
8: Independent clutch and separation system, easy to operate, simple, and practical.
9: Installation and disassembly are convenient and simple, and the installation and disassembly can be completed in 10 minutes.
Tractor front mounted garlic harvest machine is made of high-strength manganese board, with good hardness, anti-vibration, and no breakage. High-strength forged manganese steel knife, the sieve is 45 straight bar steel. The oil cylinder is a double-return high-pressure engineering cylinder. Two-speed cast steel gearbox. Nano original plastic controlled deep wheel, wear-resistant, and non-crack. The whole machine is high-temperature spray plastic, beautiful and generous!
1. The machine is 170 cm long, 135 cm wide, 90 cm high, and weighs 200 kg
2. A single harvest of garlic is 6 ridges. Normally, 2-3 mu of garlic is harvested every hour.
3. Suitable for single-cylinder 170-404 tractors with a wheelbase of no more than 130 cm. Generally use 2800 type B triangle belt. The edge wires on both sides of the sieve can be adjusted to the height of the back of the sieve, 5-8 cm from the ground.
4. The gearbox is low speed to the left and high speed to the right. It is better to use 150 cm working wheels for tractors. Use slow 2 or slow 1 gear, and the oil volume should not be too large.
5. The depth of the front knife reaches the root of the garlic, generally 10 cm.